Electro Fusion Machine Welding for HDPE Low Pressure Fitting Electrofusion Bag

Product Description

 

Product Description

 

Model	160S	315S
Working Range	32-160mm	32-315mm
Rated power	220VAC-50HZ	220VAC-50HZ
Maximum output corrent	5A	10.7A
Maximum absorbed power	900W	2450W
Outside temperature range	-5ºC-40ºC	-5ºC-40ºC
Ambient temperature probe	automatic	automatic
Dimensions(WxDxH)	245*210*300mm	245*210*300mm
Weight with carrying case	3.2kg	3.9kg

Size In 32mm To 315mm Electric Fusion Welder For Drainage Pipe

The electrofusion welder is suitable for welding low pressure or siphonic fusion tubes with a diameter of 32 to 315 mm.

The 315s automatically detects any connections to the parts to be welded and any faults in the welding process, and compensates for the current supplied based on the ambient temperature.

Compliant with current safety standards and directives, it is lightweight and easy to carry.

Condition:	New	Tube Diameter:	32-315mm
Dimensions:	245*210*300mm	Weight:	3.9kg
Usage:	Low Pressure And Siphon Pipe Fittings Welding	Port:	Shanghai Or As Required

The quality of the joint depends on your scrupulous compliance with the following recommendations.

5.1 HANDLING THE PIPES AND COUPLINGS

During welding, the pipes and couplings must be at near-ambient temperature, as detected by the welder's temperature probe. They must consequently be protected from direct sunlight both before and during welding, since they could otherwise become much warmer than the ambient temperature, with a consequent negative effect on the electro-melting process (i.e. excessive melting of the pipe and coupling). In the case of excessively high temperatures, move the pipes and couplings to a cool, shady place and wait for their temperature to return to near-ambient values.

5.2 PREPARATION

 

Cut the ends of the pipes being prepared for welding at right-angles, using suitable pipe-cutting tools (we recommend using the pipe-cutter, refer to Figure - 1 -).

Pay careful attention to avoid any bending or ovalizing of the pipe.

5.3 CLEANING

Smoothly scrape off the oxidized surface layer from the end of the pipe or fitting using suitable tools (we recommend the RTC 315 pipe-scraper, refer to Figure - 2 -). Make sure that you obtain an even, overall scraping action on the surfaces at the pipe ends involved in the welding operation, extending over at least 1 cm for each half of the coupling. If this cleaning is not done accurately, only a superficial bond will be achieved, because the oxidized layer prevents molecular penetration between the parts and thus interferes with the proper outcome of the welding action. Scraping with sand paper, rasps, or emery grinding wheels is absolutely unsuitable.

Remove the coupling from its packaging only just before it is used and clean the inside of the coupling in compliance with the manufacturer's instructions.

5.4 POSITIONING

Slide the ends of the pipes into the coupling.

It is essential to use an aligning device:

- to ensure that the parts remain in a stable position throughout the welding and cooling phases;

- to avoid any mechanical strain on the joint during the welding and cooling phases;

(we recommend using one of the aligning devices in the range, refer to Figure - 3 -).

5.5 WELDING

 

The area where welding is done must be protected against particularly unfavorable weather conditions, such as damp or temperatures below -5°C or above +40°C.

 

Use the cable and welding parameters suited to the coupling you are using.

5.6 COOLING

 

The cooling temperature varies, depending on the diameter of the couplings and the ambient temperature. Always comply with the timing recommendations of the manufacturers of the pipe and coupling elements used in the welding.

The removal of the aligning devices and disconnection of the welding cables must be done only after the cooling phase has come to an end.

Factory Tour

 

 

Application

 

Customer Visit

 

Related Products

CHUANGRONG is a leading professional supplier of plastic pipe system products since 2005.We have exported our products more than 50 countries and area.

 

Our products:
1.Plastic pipe
2.HDPE fittings
3.PPR fittings
4.PP compression fittings
5.pipe welding machine and tools
6.pipe repair clamp
Our aim is to provide customer with the best solutions of plastic pipe connection.